ILOM 3.0 Sparc Servers

First let’s start with how to access ILOM:

1. if NetMgmt port configured, using ssh you can login to the ILOM

2.If you configure SerialMgmt Port, then when you connect to serial port, you will access ILOM

3. if you connect to console thorught netmgmt or serial mgmt ports and you connect Operating System. Use #. (Hash symbol with . (dot)) which will take you to the ILOM.

From ILOM to go back to the Host Operating System then start the console service ->start /SP/console

-> start /SP/console  ==>ILOM CLI prompt
Are you sure you want to start /SP/console (y/n)? y

Serial console started.  To stop, type #.

bash-3.2#   –> OS prompt
Serial console stopped.

->  ==>ILOM CLI prompt

Notes on ILOM CLI follow hierarchial Architecture

ILOM Target types:

/SP – configuring ILOM service processor (SP)

/SYS – inventory/environmental and hardware management

/HOST – monitoring and managing host operating system.

Blade Platforms:

/CMM – Blade platform this replace SP, used to configure ILOM Chassis Monitoring Module

/CH – Blade platform this replace /SYS and provides inventory, environmentals and hardware management

ILOM CLI commands:


ILOM CLI Syntax:

command [options] [target] [properties

ex.,: set /SP/services/https port=80 servicestate=enabled

User Management ILOM CLI:

Roles in CLI: Admin|Operator (a), User Management (u), Console (c), Reset and Host control (r) and Read Only (o)

1. Add a local user

create /SP/users/user1 password=password  role=a|u|c|r|o|s

2.  Delete a local user

delete /SP/users/user1

 3. Change a local user’s properties

set /SP/users/user1  role=operator

 4. Display information about all local users

show -display [targets|properties|all ] -level all /SP/users

 5. Display information aboutLDAP settings

show /SP/clients/ldap

6. Change LDAP settings

set /SP/clients/ldap binddn=proxyuser bindpw=proxyuserpassword defaultrole=a|u|c|r|o|s address=ipaddress

 Set ILOM clock to sync with NTP server

set /SP/clients/ntp/server/1 address=ntpIPAddress

To configure IP on NetMgmt port set values to the /SP/network properties

        commitpending = (Cannot show property)
        dhcp_server_ip = (none)
        ipaddress = (none)
        ipdiscovery = (none)
        ipgateway = (none)
        ipnetmask = (none)
        macaddress = xx:xxx:xx:xx:xx:xx
        managementport = /SYS/MB/SP/NETMGMT
        outofbandmacaddress = xx:xx:xx:xx:xx:xx
        pendingipaddress = (none) –>IPV4 address
        pendingipdiscovery = (none)
        pendingipgateway = (none)  –> Gateway
        pendingipnetmask = (none) –> Netmask
        pendingmanagementport = /SYS/MB/SP/NETMGMT
        sidebandmacaddress = xx:xx:xx:xx:xx:xx
        state = disabled

you can configure above values using set command

set /SP/network pendingipaddress=

set /SP/network pendingipnetmask=

set /SP/network pendingipgateway=

Configuring SNMP and email alert:

set /SP/alertmgmt/rules/1…15 type=snmtrap snmp_version=3 comunity_or_username=username destination=ipaddress level=down|critical|major|minor

set /SP/alertmgmt/rules/1…15 type=email level=down|critical|major|minor

To enable web access to ILOM, can http

set /SP/services/http port=80 secureredirect=enabled|disabled servicestate=enabled|disabled

set /SP/services/https port=xxx servicestate=enabled|disabled

HOST system commands (*warning: if your host is up and running, HOST commands can cause outage)

To start the host system ->start /SYS

To stop the host system -> stop /SYS

Force shutdown (required when host hung)->stop -f /SYS

Reset the host system  (required when host hung) ->reset /SYS

start a sessions to connect to host console -> /SP/console

stop the console session -> /SP/console

Filtering output options:

Users with admin roles -> show /SP/users -level all role==”a*”

SNMP trap alerts ->show /SP/alertmgmt -level all type==”snmptrap”

List services which are disabled -> show /SP/services -level all servicestate==disabled

List memory moduels with some part number -> show /SYS -level all type==”DIMM” fru_part_number==07014642

list all hard disks -> show /SYS -level all type==”Hard Disk”

How to backup the ILOM configuration

cd /SP/config

set passphrase=passphrase

set dump_uri=transfer_method://username:password@ipaddress_or_hostname/directorypath/filename

set dump_uri=scp://adminuser:userpswd@x.x.x.x/Backup/Lab9/SP-backup.config

How to Restore the ILOM configuration

Note: you have to login ILOM with user which has Admin,User Management, Console, Reset, Host control and Read only (a,u,c,r,o) roles.

cd /SP/config

set passphrase=passphrase

set load_uri=transfer_method://username:password@ipaddress_or_hostname/directorypath/filename

How to update ILOM Firmware

Pre requisite: Shutdown the host running on the hardware whose ILOM firmware you are upgrading

1.Login to ILOM CLI with user which has Admin role

2. ->version

3. Download the zip file packge and copy to TFTP server that is accessible from network

4.load -source <supported_protocol>://<server ip>/<path_to_firmware_image/<>

Do you want to preserve the configuration (y/n)?y

Once firmware loades it automaticall reboots to complete the firmware update

ILOM CLI is based on DMTF CLP (Distributed Management Task Force specification Server Management Command-Line Specification, Version 11.0a.8 Draft



Author: rajukv

Hadoop(BigData) Architect and Hadoop Security Architect can design and build hadoop system to meet various data science projects.

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s